add directory Minix

Minix/1.7.5/MINIX/README.TXT

@@ -0,0 +1,79 @@
+The installation guide can be found in INSTALL.TXT
+
+More manual pages are in MAN\CAT*\*
+If a manual page refers to, say boot(8), then the manual page for boot
+can be found in MAN\CAT8\BOOT.8.  Under Minix you can type 'man 8 boot'
+if you have installed the SYS.TAZ set.
+
+For a 386, 486, or Pentium using 1.44 MB floppies on drive A: you must make
+four sets of floppies.  Go to the MINIX directory and type each of these
+commands in turn.  You will be prompted to insert floppies.  You do not have
+to install SYS.TAZ and CMD.TAZ initially, but life is much simpler if you
+have 9 floppies and make each set right now.  Be sure to label each floppy
+correctly.
+
+        fdvol 1440 A: i386\ROOT i386\USR    (Combined boot floppy)
+        fdvol 1440 A: i386\USR.TAZ          (Base system on 3 floppies)
+        fdvol 1440 A: SYS.TAZ               (System sources on 2 floppies)
+        fdvol 1440 A: CMD.TAZ               (Commands sources on 3 floppies)
+
+Use 1200 to specify 1.2M floppies.  Likewise for 720k floppies, except
+that you have to put ROOT and USR installation images on two separate
+floppies:
+
+        fdvol 720 A: i386\ROOT              (Separate ROOT and USR)
+        fdvol 720 A: i386\USR
+        fdvol 720 A: i386\USR.TAZ          
+        fdvol 720 A: SYS.TAZ              
+        fdvol 720 A: CMD.TAZ            
+
+The i86 directory contains the installation and base system material to
+install the 16-bits version of Minix for old XTs and 286 based ATs.  If
+the intended machine has little memory or a 360k drive then read
+XT\README.TXT and use the installation floppy images in the XT directory
+instead of the regular ROOT and USR.
+
+After you have installed MINIX, you may wish to install some of the other
+files on the CD ROM.  The SMX and BOCHS programs are simulators that sun
+on UNIX workstations, so you must transfer them there using a modem and
+unpack and use them there.  The other .TAZ files should be copied to
+floppies using fdvol.  To reconstruct a .TAZ file on a sequence of 1.44 MB
+floppies via drive A:, boot MINIX, log in, and type:
+
+        vol -r 1440 /dev/fd0 | zcat | tar xf -
+
+Please note that the MINIX program is called vol, not fdvol.
+For drive B:, use /dev/fd1 instead of /dev/fd0.  The result will be a
+fully-expanded and decompressed file tree.
+
+
+In summary:
+    1. You should now have a BOOT floppy (or ROOT + USR floppies).
+    2. A set of floppies for USR.TAZ, SYS.TAZ, and CMD.TAZ.
+    3. A free hard disk partition, or at least enough space not in any
+       partition that you can create a new partition in this space.
+    4. Now read INSTALL.TXT and follow it carefully.
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+
+