add directory net
This commit is contained in:
gohigh
303
net/tcpip/ether-995/hp.c
Normal file
303
net/tcpip/ether-995/hp.c
Normal file
@@ -0,0 +1,303 @@
|
||||
/* hp.c: A HP LAN ethernet driver for linux. */
|
||||
/*
|
||||
Written 1993 by Donald Becker. This is alpha test code.
|
||||
This is a extension to the Linux operating system, and is covered by
|
||||
same Gnu Public License that covers that work.
|
||||
|
||||
This is a driver for the HP LAN adaptors.
|
||||
|
||||
The Author may be reached as becker@super.org or
|
||||
C/O Supercomputing Research Ctr., 17100 Science Dr., Bowie MD 20715
|
||||
*/
|
||||
|
||||
static char *version = "hp.c:v0.43 2/12/93 Donald Becker (becker@super.org)\n";
|
||||
|
||||
#include <linux/config.h>
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/sched.h>
|
||||
#include <asm/io.h>
|
||||
#include <asm/system.h>
|
||||
|
||||
#include "dev.h"
|
||||
#include "8390.h"
|
||||
|
||||
/* These should be in <asm/io.h> someday, borrowed from blk_drv/hd.c. */
|
||||
#define port_read(port,buf,nr) \
|
||||
__asm__("cld;rep;insw"::"d" (port),"D" (buf),"c" (nr):"cx","di")
|
||||
#define port_write(port,buf,nr) \
|
||||
__asm__("cld;rep;outsw"::"d" (port),"S" (buf),"c" (nr):"cx","si")
|
||||
|
||||
#define port_read_b(port,buf,nr) \
|
||||
__asm__("cld;rep;insb"::"d" (port),"D" (buf),"c" (nr):"cx","di")
|
||||
#define port_write_b(port,buf,nr) \
|
||||
__asm__("cld;rep;outsb"::"d" (port),"S" (buf),"c" (nr):"cx","si")
|
||||
|
||||
#define HP_DATAPORT 0x0c /* "Remote DMA" data port. */
|
||||
#define HP_ID 0x07
|
||||
#define HP_CONFIGURE 0x08 /* Configuration register. */
|
||||
#define HP_RUN 0x01 /* 1 == Run, 0 == reset. */
|
||||
#define HP_IRQ 0x0E /* Mask for software-configured IRQ line. */
|
||||
#define HP_DATAON 0x10 /* Turn on dataport */
|
||||
#define NIC_OFFSET 0x10 /* Offset the 8390 registers. */
|
||||
|
||||
#define HP_START_PG 0x00 /* First page of TX buffer */
|
||||
#define HP_8BSTOP_PG 0x80 /* Last page +1 of RX ring */
|
||||
#define HP_16BSTOP_PG 0xFF /* Last page +1 of RX ring */
|
||||
|
||||
extern void NS8390_init(struct device *dev, int startp);
|
||||
extern int ei_debug;
|
||||
extern struct sigaction ei_sigaction;
|
||||
extern struct ei_device ei_status;
|
||||
|
||||
int hpprobe(int ioaddr, struct device *dev);
|
||||
int hpprobe1(int ioaddr, struct device *dev);
|
||||
|
||||
static void hp_reset_8390(struct device *dev);
|
||||
static int hp_block_input(struct device *dev, int count,
|
||||
char *buf, int ring_offset);
|
||||
static void hp_block_output(struct device *dev, int count,
|
||||
const unsigned char *buf, const start_page);
|
||||
static void hp_init_card(struct device *dev);
|
||||
|
||||
|
||||
/* Probe for an HP LAN adaptor.
|
||||
Also initialize the card and fill in STATION_ADDR with the station
|
||||
address. */
|
||||
|
||||
int hpprobe(int ioaddr, struct device *dev)
|
||||
{
|
||||
int *port, ports[] = {0x300, 0x320, 0x340, 0x280, 0x2C0, 0x200, 0x240, 0};
|
||||
|
||||
if (ioaddr > 0x100)
|
||||
return hpprobe1(ioaddr, dev);
|
||||
|
||||
for (port = &ports[0]; *port; port++)
|
||||
if (inb_p(*port) != 0xff && hpprobe1(*port, dev))
|
||||
return dev->base_addr;
|
||||
return 0;
|
||||
}
|
||||
|
||||
int hpprobe1(int ioaddr, struct device *dev)
|
||||
{
|
||||
int i;
|
||||
unsigned char *station_addr = dev->dev_addr;
|
||||
unsigned char SA_prom[6];
|
||||
int tmp;
|
||||
int hplan;
|
||||
|
||||
printk("HP-LAN ethercard probe at %#3x:", ioaddr);
|
||||
tmp = inb_p(ioaddr);
|
||||
if (tmp == 0xFF) {
|
||||
printk(" not found (nothing there).\n");
|
||||
return 0;
|
||||
}
|
||||
|
||||
for(i = 0; i < sizeof(SA_prom); i++) {
|
||||
SA_prom[i] = inb(ioaddr + i);
|
||||
if (i < ETHER_ADDR_LEN && station_addr) {
|
||||
printk(" %2.2x", SA_prom[i]);
|
||||
station_addr[i] = SA_prom[i];
|
||||
}
|
||||
}
|
||||
hplan = (SA_prom[0] == 0x08 && SA_prom[1] == 0x00 && SA_prom[2] == 0x09);
|
||||
if (hplan == 0) {
|
||||
printk(" not found (invalid station address prefix).\n");
|
||||
return 0;
|
||||
}
|
||||
|
||||
ei_status.tx_start_page = HP_START_PG;
|
||||
ei_status.rx_start_page = HP_START_PG + TX_PAGES;
|
||||
/* Set up the rest of the parameters. */
|
||||
if ((tmp = inb_p(HP_ID)) & 0x80) {
|
||||
ei_status.name = "HP27247";
|
||||
ei_status.word16 = 1;
|
||||
ei_status.stop_page = HP_16BSTOP_PG; /* Safe for now */
|
||||
} else {
|
||||
ei_status.name = "HP27250";
|
||||
ei_status.word16 = 0;
|
||||
ei_status.stop_page = HP_8BSTOP_PG; /* Safe for now */
|
||||
}
|
||||
|
||||
/* Set the base address to point to the NIC! */
|
||||
dev->base_addr = ioaddr + NIC_OFFSET;
|
||||
|
||||
if (dev->irq == 2)
|
||||
dev->irq = 9;
|
||||
|
||||
/* Snarf the interrupt now. There's no point in waiting since we cannot
|
||||
share and the board will usually be enabled. */
|
||||
if (dev->irq < 2) {
|
||||
int irq_16list[] = { 11, 10, 5, 3, 4, 7, 9, 0};
|
||||
int irq_8list[] = { 7, 5, 3, 4, 9, 0};
|
||||
int *irq = ei_status.word16 ? irq_16list : irq_8list;
|
||||
for (; *irq; irq++) {
|
||||
if (irqaction(dev->irq = *irq, &ei_sigaction) == 0)
|
||||
break;
|
||||
}
|
||||
if (*irq == 0) {
|
||||
printk (" unable to get an IRQ.\n");
|
||||
return 0;
|
||||
}
|
||||
}
|
||||
|
||||
printk(" %s found, using IRQ %d.\n", ei_status.name, dev->irq);
|
||||
if (ei_debug > 1)
|
||||
printk(version);
|
||||
|
||||
ei_status.reset_8390 = &hp_reset_8390;
|
||||
ei_status.block_input = &hp_block_input;
|
||||
ei_status.block_output = &hp_block_output;
|
||||
hp_init_card(dev);
|
||||
return dev->base_addr;
|
||||
}
|
||||
|
||||
static void
|
||||
hp_reset_8390(struct device *dev)
|
||||
{
|
||||
int hp_base = dev->base_addr - NIC_OFFSET;
|
||||
int saved_config = inb_p(hp_base + HP_CONFIGURE);
|
||||
int reset_start_time = jiffies;
|
||||
|
||||
if (ei_debug > 1) printk("resetting the 8390 time=%d...", jiffies);
|
||||
outb_p(0x00, hp_base + HP_CONFIGURE);
|
||||
ei_status.txing = 0;
|
||||
|
||||
sti();
|
||||
/* We shouldn't use the boguscount for timing, but this hasn't been
|
||||
checked yet, and you could hang your machine if jiffies break... */
|
||||
{
|
||||
int boguscount = 150000;
|
||||
while(jiffies - reset_start_time < 2)
|
||||
if (boguscount-- < 0) {
|
||||
printk("jiffy failure (t=%d)...", jiffies);
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
outb_p(saved_config, hp_base + HP_CONFIGURE);
|
||||
while ((inb_p(hp_base+NIC_OFFSET+EN0_ISR) & ENISR_RESET) == 0)
|
||||
if (jiffies - reset_start_time > 2) {
|
||||
printk(EI_NAME": hp_reset_8390() did not complete.\n");
|
||||
return;
|
||||
}
|
||||
if (ei_debug > 1) printk("8390 reset done.", jiffies);
|
||||
}
|
||||
|
||||
/* Block input and output, similar to the Crynwr packet driver. If you
|
||||
porting to a new ethercard look at the packet driver source for hints.
|
||||
The HP LAN doesn't use shared memory -- we put the packet
|
||||
out through the "remote DMA" dataport. */
|
||||
|
||||
static int
|
||||
hp_block_input(struct device *dev, int count, char *buf, int ring_offset)
|
||||
{
|
||||
int nic_base = dev->base_addr;
|
||||
int saved_config = inb_p(nic_base - NIC_OFFSET + HP_CONFIGURE);
|
||||
int xfer_count = count;
|
||||
|
||||
outb_p(saved_config | HP_DATAON, nic_base - NIC_OFFSET + HP_CONFIGURE);
|
||||
outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, nic_base);
|
||||
outb_p(count & 0xff, nic_base + EN0_RCNTLO);
|
||||
outb_p(count >> 8, nic_base + EN0_RCNTHI);
|
||||
outb_p(ring_offset & 0xff, nic_base + EN0_RSARLO);
|
||||
outb_p(ring_offset >> 8, nic_base + EN0_RSARHI);
|
||||
outb_p(E8390_RREAD+E8390_START, nic_base);
|
||||
if (ei_status.word16) {
|
||||
port_read(nic_base - NIC_OFFSET + HP_DATAPORT,buf,count>>1);
|
||||
if (count & 0x01)
|
||||
buf[count-1] = inb(nic_base - NIC_OFFSET + HP_DATAPORT), xfer_count++;
|
||||
} else {
|
||||
port_read_b(nic_base - NIC_OFFSET + HP_DATAPORT, buf, count);
|
||||
}
|
||||
/* This is for the ALPHA version only, remove for later releases. */
|
||||
if (ei_debug > 0) { /* DMA termination address check... */
|
||||
int high = inb_p(nic_base + EN0_RSARHI);
|
||||
int low = inb_p(nic_base + EN0_RSARLO);
|
||||
int addr = (high << 8) + low;
|
||||
/* Check only the lower 8 bits so we can ignore ring wrap. */
|
||||
if (((ring_offset + xfer_count) & 0xff) != (addr & 0xff))
|
||||
printk(EI_NAME": RX transfer address mismatch, %#4.4x vs. %#4.4x (actual).\n",
|
||||
ring_offset + xfer_count, addr);
|
||||
}
|
||||
outb_p(saved_config & (~HP_DATAON), nic_base - NIC_OFFSET + HP_CONFIGURE);
|
||||
return ring_offset + count;
|
||||
}
|
||||
|
||||
static void
|
||||
hp_block_output(struct device *dev, int count,
|
||||
const unsigned char *buf, const start_page)
|
||||
{
|
||||
int nic_base = dev->base_addr;
|
||||
int saved_config = inb_p(nic_base - NIC_OFFSET + HP_CONFIGURE);
|
||||
|
||||
outb_p(saved_config | HP_DATAON, nic_base - NIC_OFFSET + HP_CONFIGURE);
|
||||
/* Round the count up for word writes. Do we need to do this?
|
||||
What effect will an odd byte count have on the 8390?
|
||||
I should check someday. */
|
||||
if (ei_status.word16 && (count & 0x01))
|
||||
count++;
|
||||
/* We should already be in page 0, but to be safe... */
|
||||
outb_p(E8390_PAGE0+E8390_START+E8390_NODMA, nic_base);
|
||||
|
||||
#ifdef ei8390_bug
|
||||
/* Handle the read-before-write bug the same way as the
|
||||
Crynwr packet driver -- the NatSemi method doesn't work. */
|
||||
outb_p(0x42, nic_base + EN0_RCNTLO);
|
||||
outb_p(0, nic_base + EN0_RCNTHI);
|
||||
outb_p(0xff, nic_base + EN0_RSARLO);
|
||||
outb_p(0x00, nic_base + EN0_RSARHI);
|
||||
outb_p(E8390_RREAD+E8390_START, EN_CMD);
|
||||
/* Make certain that the dummy read has occured. */
|
||||
inb_p(0x61);
|
||||
inb_p(0x61);
|
||||
#endif
|
||||
|
||||
outb_p(count & 0xff, nic_base + EN0_RCNTLO);
|
||||
outb_p(count >> 8, nic_base + EN0_RCNTHI);
|
||||
outb_p(0x00, nic_base + EN0_RSARLO);
|
||||
outb_p(start_page, nic_base + EN0_RSARHI);
|
||||
|
||||
outb_p(E8390_RWRITE+E8390_START, nic_base);
|
||||
if (ei_status.word16) {
|
||||
/* Use the 'rep' sequence for 16 bit boards. */
|
||||
port_write(nic_base - NIC_OFFSET + HP_DATAPORT, buf, count>>1);
|
||||
} else {
|
||||
port_write_b(nic_base - NIC_OFFSET + HP_DATAPORT, buf, count);
|
||||
}
|
||||
|
||||
/* DON'T check for 'inb_p(EN0_ISR) & ENISR_RDC' here -- it's broken! */
|
||||
|
||||
/* This is for the ALPHA version only, remove for later releases. */
|
||||
if (ei_debug > 0) { /* DMA termination address check... */
|
||||
int high = inb_p(nic_base + EN0_RSARHI);
|
||||
int low = inb_p(nic_base + EN0_RSARLO);
|
||||
int addr = (high << 8) + low;
|
||||
if ((start_page << 8) + count != addr)
|
||||
printk(EI_NAME": TX Transfer address mismatch, %#4.4x vs. %#4.4x.\n",
|
||||
(start_page << 8) + count, addr);
|
||||
}
|
||||
outb_p(saved_config & (~HP_DATAON), nic_base - NIC_OFFSET + HP_CONFIGURE);
|
||||
return;
|
||||
}
|
||||
|
||||
/* This function resets the ethercard if something screws up. */
|
||||
static void
|
||||
hp_init_card(struct device *dev)
|
||||
{
|
||||
int irq = dev->irq;
|
||||
/* default is IRQ5 0 1 2 3 4 5 6 7 8 9 10 11 */
|
||||
static char irqval[16] = { 0, 0, 4, 6, 8,10, 0,14, 0, 4, 2,12,0,0,0,0};
|
||||
NS8390_init(dev, 0);
|
||||
outb_p(irqval[irq&0x0f] | HP_RUN,
|
||||
dev->base_addr - NIC_OFFSET + HP_CONFIGURE);
|
||||
return;
|
||||
}
|
||||
|
||||
|
||||
/*
|
||||
* Local variables:
|
||||
* compile-command: "gcc -DKERNEL -Wall -O6 -fomit-frame-pointer -I/usr/src/linux/net/tcp -c hp.c"
|
||||
* version-control: t
|
||||
* kept-new-versions: 5
|
||||
* End:
|
||||
*/
|
||||
Reference in New Issue
Block a user