408 lines
32 KiB
Plaintext
408 lines
32 KiB
Plaintext
|
||
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
|
||
³ DIAGRAMS.DOC Supplement to TheRef(tm) Drive & Controller Listing ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ In "publishing" TheRef(tm), I've often been asked the difference ³±
|
||
³ between the types of drive controllers and recording methods. I'm ³±
|
||
³ not going to get into that in this document, as it would require a ³±
|
||
³ good sized doc. of it's own. What I have supplied are diagrams of ³±
|
||
³ the different connectors associated with the technology today. ³±
|
||
³ frf ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ CABLES ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ ³±
|
||
³ Controller Drive 2(or none) Drive 1 ³±
|
||
³ ³±
|
||
³ 1ÉÍÍ» ÄÄÄÄÄÄÄÄÄ1ÉÍÍ» ÄÄÄÄstripeÄÄÄÄÄ1ÉÍÍ» Pins 10-16 ³±
|
||
³ FLOPPY cable º::ºðððððððððððºÃ´ºðððððððððððððððððºÃ´º are twisted ³±
|
||
³ with twist º::ºðððððððððððºÃ´ºðððððððððððððXXððºÃ´º before the ³±
|
||
³ (control & º::ºðððððððððððºÃ´ºðððððððððððððððððºÃ´º connector. ³±
|
||
³ data, 34 pin) º::ºðððððððððððºÃ´ºðððððððððððððððððºÃ´º (7 wires) ³±
|
||
³ ÈÍͼ ÈÍͼ ÈÍͼ ³±
|
||
³ 1ÉÍÍ» ÄÄÄÄÄÄÄÄÄ1ÉÍÍ» ÄÄÄÄstripeÄÄÄÄÄ1ÉÍÍ» Pins 25-29 ³±
|
||
³ ST412 & ESDI º::ºðððððððððððºÃ´ºðððððððððððððððððºÃ´º are twisted ³±
|
||
³ Hard Drive º::ºðððððððððððºÃ´ºðððððððððððððððððºÃ´º before the ³±
|
||
³ cable w/twist º::ºðððððððððððºÃ´ºðððððððððððððXXððºÃ´º connector. ³±
|
||
³ (control) º::ºðððððððððððºÃ´ºðððððððððððððððððºÃ´º (5 wires) ³±
|
||
³ ÈÍͼ ÈÍͼ ÈÍͼ ³±
|
||
³ 1ÉÍÍ» ÄÄÄÄÄÄÄÄÄÄÄstripeÄÄÄÄÄÄÄÄÄÄÄÄÄ1ÉÍÍ» (no twists) ³±
|
||
³ ST412 & ESDI º::ºððððððððððððððððððððððððððððððððºÃ´º Each drive ³±
|
||
³ Hard Drive º::ºððððððððððððððððððððððððððððððððºÃ´º has it's ³±
|
||
³ (data, 20 pin)º::ºððððððððððððððððððððððððððððððððºÃ´º own data ³±
|
||
³ ÈÍͼ ÈÍͼ cable ³±
|
||
³ ³±
|
||
³ IMPORTANT NOTE: Pin #1 on any drive cable SHOULD be indicated by a ³±
|
||
³ a colored stripe. If you should find the stripe ³±
|
||
³ by connector pin 34 (or 20), inspect the whole ³±
|
||
³ cable VERY throughly! ³±
|
||
³ ³±
|
||
³ DRIVE SELECT For both Floppy and Hard drives, when the 34 pin ³±
|
||
³ JUMPERS: cable has a twist, the device number should be set ³±
|
||
³ to the second position. Drives numbered 0-3, set to ³±
|
||
³ 1, those numbered 1-4, set to 2. When cables with- ³±
|
||
³ out a twist are used, Floppy "A", and(or) Hard drive ³±
|
||
³ "C" should be set to 1, and the second Floppy and ³±
|
||
³ (or) Hard drive should be set to 2. ³±
|
||
³ ³±
|
||
³ TERMINATORS: When using more than one drive on a cable (ie; 2FDs ³±
|
||
³ or 2HDs), the terminating resistor pack should be ³±
|
||
³ left on the drive furthest from the controller, and ³±
|
||
³ removed from the drive closest to the controller. ³±
|
||
³ ³±
|
||
³ NOTE: On SCSI drives, the Host Adapter also has resistors. ³±
|
||
³ These are needed to terminate both ends of the bus. ³±
|
||
³ Since the SCSI bus can have up to 7 devices attached ³±
|
||
³ to it, only the Host Adapter and the device farthest ³±
|
||
³ from it will retain the resistors. All devices in- ³±
|
||
³ between should have theirs removed. ³±
|
||
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ±
|
||
±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±
|
||
|
||
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
|
||
³ DIAGRAMS.DOC 2 ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ CONNECTIONS ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ ³±
|
||
³ FLOPPY DRIVES ÚÄÄÄÄÄ¿ ³±
|
||
³ HI/LO DENSITY >³2 1³ GND ³±
|
||
³ The connector on a floppy drive N/C ³4 _ 3³ | ³±
|
||
³ consists of 34 conductors. Both N/C ³6 5³ | ³±
|
||
³ control and data use this same INDEX <³8 7³ | ³±
|
||
³ cable. Most cables have a twist MOTOR ENAB. A >³10 9³ | ³±
|
||
³ that interchanges pins 10 through DRIVE SEL. B >³12 11³ | ³±
|
||
³ 16 at the end of the cable (on DRIVE SEL. A >³14 13³ | ³±
|
||
³ drive 1). Most floppy connect- MOTOR ENAB. B >³16 15³ | ³±
|
||
³ ors have a "key" between pins DIRECTION SEL. >³18 17³ | ³±
|
||
³ 4 & 6, and 3 & 5, to prevent the HEAD STEP >³20 19³ | ³±
|
||
³ cable from being reversed. At WRITE DATA >³22 21³ | ³±
|
||
³ the other end, the dual row con- WRITE GATE >³24 23³ | ³±
|
||
³ nector that attaches to the con- TRACK 00 <³26 25³ | ³±
|
||
³ troller card will usually have a WRITE PROTECT <³28 27³ | ³±
|
||
³ set of ridges that coincide with READ DATA <³30 29³ | ³±
|
||
³ cutouts in the controller card's HEAD SELECT >³32 31³ | ³±
|
||
³ connector. Note that old style DISK CHANGE <³34 33³ GND ³±
|
||
³ floppy-only controllers used a ÀÄÄÄÄÄÙ ³±
|
||
³ card-edge connector just like that > Input ( At the ³±
|
||
³ of the drive. < Output Drive Conn.) ³±
|
||
³ ³±
|
||
³ ST506/412 HARD DRIVE (MFM & RLL) ³±
|
||
³ ³±
|
||
³ This standard drive system uses ÚÄÄÄÄÄ¿ ³±
|
||
³ two cables; a 34 conductor control HEAD SEL. 8 ³1 2³ GND ³±
|
||
³ cable, and a 20 conductor data HEAD SEL. 4 ³3 _ 4³ | ³±
|
||
³ cable. The control cable contains WRITE GATE ³5 6³ | ³±
|
||
³ a twist of the conductors going to SEEK COMPLETE ³7 8³ | ³±
|
||
³ the farthest drive, which is drive TRACK 0 ³9 10³ | ³±
|
||
³ "C" on most systems. This twist WRITE FAULT ³11 12³ | ³±
|
||
³ consists of conductors 25 through HEAD SEL. 1 ³13 14³ | ³±
|
||
³ 29. As with the floppy cable, the RESERVED ³15 16³ | ³±
|
||
³ ST506/412 cables normally have a HEAD SEL. 2 ³17 18³ | ³±
|
||
³ key to prevent reversal, and the INDEX ³19 20³ | ³±
|
||
³ controller end has a pin-type con- READY ³21 22³ | ³±
|
||
³ nector, while the drive end has a STEP ³23 24³ | ³±
|
||
³ card-edge type connector. DRIVE SEL. 1 ³25 26³ | ³±
|
||
³ DRIVE SEL. 2 ³27 28³ | ³±
|
||
³ ÚÄÄÄÄÄ¿ DRIVE SEL. 3 ³29 30³ | ³±
|
||
³ DRIVE SEL'D ³1 2³ GND DRIVE SEL. 4 ³31 32³ | ³±
|
||
³ RESERVED ³3 _ 4³ | DIRECTION IN ³33 34³ GND ³±
|
||
³ | ³5 6³ | ÀÄÄÄÄÄÙ ³±
|
||
³ | ³7 8³ GND ³±
|
||
³ RESERVED ³9 10³ RESERVED Though control signals ³±
|
||
³ GND ³11 12³ GND go through a single 34 ³±
|
||
³ * WRITE DATA+ ³13 14³ * WRITE DATA- conductor cable, data ³±
|
||
³ GND ³15 16³ GND flows through seperate ³±
|
||
³ * READ DATA+ ³17 18³ * READ DATA- 20 conductor cables ³±
|
||
³ GND ³19 20³ GND for each drive (C,D). ³±
|
||
³ *(MFM or RLL) ÀÄÄÄÄÄÙ ³±
|
||
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ±
|
||
±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±
|
||
|
||
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
|
||
³ DIAGRAMS.DOC 3 ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ CONNECTIONS ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ ³±
|
||
³ ESDI HARD DRIVES ÚÄÄÄÄÄ¿ ³±
|
||
³ HEAD SEL. 3 ³1 2³ GND ³±
|
||
³ Though ESDI and ST506/412 drives HEAD SEL. 2 ³3 _ 4³ | ³±
|
||
³ share similar looking cables, WRITE GATE ³5 6³ | ³±
|
||
³ even to the point of having a CONFIG/STAT DATA ³7 8³ | ³±
|
||
³ twist, the actual data and con- TRANSFER ACK. ³9 10³ | ³±
|
||
³ trol signals are very different. ATTENTION ³11 12³ | ³±
|
||
³ One should never mix components HEAD SEL. 0 ³13 14³ | ³±
|
||
³ from these two drive types. SECT/ADD.MK. FOUND ³15 16³ | ³±
|
||
³ While the ST506/412 interface HEAD SEL. 1 ³17 18³ | ³±
|
||
³ utilizes a standard pulse code INDEX ³19 20³ | ³±
|
||
³ to transmit data between the READY ³21 22³ | ³±
|
||
³ drive and controller, ESDI uses TRANS.REQUEST ³23 24³ | ³±
|
||
³ a pulse code that does not require DRIVE SEL. 1 ³25 26³ | ³±
|
||
³ the level to return to zero between DRIVE SEL. 2 ³27 28³ | ³±
|
||
³ pulses. This format is refered to DRIVE SEL. 3 ³29 30³ | ³±
|
||
³ as NRZ, or Non Return to Zero. By READ GATE ³31 32³ | ³±
|
||
³ utilizing NRZ, the clock that data COMMAND DATA ³33 34³ GND ³±
|
||
³ is transfered by can be increased, ÀÄÄÄÄÄÙ ³±
|
||
³ thereby increasing the troughput to ³±
|
||
³ and from the ESDI disk. ³±
|
||
³ ÚÄÄÄÄÄ¿ ³±
|
||
³ DRIVE SEL'D ³1 2³ SECT/ADD.MK. FOUND ³±
|
||
³ SEEK COMPLETE ³3 4³ ADDRESS MARK ENABLE ³±
|
||
³ RESV'D FOR STEP MODE ³5 6³ GND ³±
|
||
³ WRITE CLOCK+ ³7 8³ WRITE CLOCK- ³±
|
||
³ CARTRIDGE CHANGED ³9 10³ READ REF. CLOCK+ ³±
|
||
³ READ REF. CLOCK- ³11 12³ GND ³±
|
||
³ NRZ WRITE DATA+ ³13 14³ NRZ WRITE DATA- ³±
|
||
³ GND ³15 16³ GND ³±
|
||
³ NRZ READ DATA+ ³17 18³ NRZ READ DATA- ³±
|
||
³ GND ³19 20³ GND ³±
|
||
³ ÀÄÄÄÄÄÙ ³±
|
||
³ ³±
|
||
³ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ And in this corner... Recording ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³±
|
||
³ ³±
|
||
³ Times were, you had a simple choice for type of disk drive... ³±
|
||
³ Any kind, as long as it was ST506/412. Those were the heydays of ³±
|
||
³ MFM drives. But many manufacturers weren't content with the 17 ³±
|
||
³ sectors/track that MFM provided. They devised a newer encoding ³±
|
||
³ scheme to pack data tighter, and called it RLL, or Run Length ³±
|
||
³ Limited, as opposed to MFM, or Modified Frequency Modulation. It ³±
|
||
³ involves using groups of 16 bits rather than each individual bit, ³±
|
||
³ thus achieving a sort of "compression" of the information as it is ³±
|
||
³ encoded. Since the same information takes up less space as RLL ³±
|
||
³ encoded data, more info can be writen to the disk. The most com- ³±
|
||
³ mon RLL technique, known as 2,7 RLL, can pack roughly 50% more on ³±
|
||
³ a disk than MFM. Of course, there is always a trade-off, and the ³±
|
||
³ timing and media required for RLL is it. RLL requires a higher ³±
|
||
³ grade of media because of it's dense bit-packing, and timing is ³±
|
||
³ more critical, since the data is flowing at 50% higher rate than ³±
|
||
³ an MFM drive. Also, the mechanics of the drive must have tighter ³±
|
||
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ±
|
||
±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±
|
||
|
||
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
|
||
³ DIAGRAMS.DOC 4 ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ tolerences because head positioning becomes more critical. These ³±
|
||
³ requirements kept RLL drives at a premium. It has only been the ³±
|
||
³ last two years, that RLL drives have outsold MFM, and have all but ³±
|
||
³ wiped them from the marketplace. This turnabout has come from the ³±
|
||
³ need to increase disk capacity more and more. Both ESDI, and SCSI ³±
|
||
³ type drives utilize RLL.(1*) encoding to achieve high capacity and ³±
|
||
³ transfer rates (from the disk). And the newest interface, IDE, or ³±
|
||
³ Integrated Drive Electronics, is also based on this technology. ³±
|
||
³ ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ³±
|
||
³ ÚÄÄÄÄÄ¿ ³±
|
||
³ SCSI HARD DRIVES DB0 <>³2 1³ GND 5 ³±
|
||
³ DB1 <>³4 3³ | 0 ³±
|
||
³ The normal internal cable for SCSI DB2 <>³6 5³ | ³±
|
||
³ is a 50 conductor ribbon, with all DB3 <>³8 7³ | P ³±
|
||
³ odd numbered conductors grounded. DB4 <>³10 9³ | I ³±
|
||
³ Two conductors, numbers 25 & 26, are DB5 <>³12 11³ | N ³±
|
||
³ often left not-connected, as they DB6 <>³14 13³ | ³±
|
||
³ deal with Terminator power, and can DB7 <>³16 15³ | D ³±
|
||
³ be easily shorted by cable reversals. DBP <>³18 17³ | U ³±
|
||
³ There are no twists in this cable, GND ³20 19³ | A ³±
|
||
³ and it's length may be a maximum of GND ³22 21³ | L ³±
|
||
³ 6 meters. But one is advised to use GND ³24 23³ | ³±
|
||
³ minimum lengths to improve timing. TERM PWR ³26 25³ | R ³±
|
||
³ Up to seven drives, or devices may be GND ³28 27³ | O ³±
|
||
³ attached to an SCSI cable. Each is GND ³30 29³ | W ³±
|
||
³ daisy-chained on the cable, or, when ATN >³32 31³ | ³±
|
||
³ a device has two connectors, another GND ³34 33³ | C ³±
|
||
³ cable may be "spliced" into the chain BSY <>³36 35³ | O ³±
|
||
³ starting at the second connector, and ACK >³38 37³ | N ³±
|
||
³ continued on. Care must be taken to RST <>³40 39³ | N ³±
|
||
³ insure that cables and connectors are MSG < ³42 41³ | E ³±
|
||
³ not reversed, as this would short pin SEL <>³44 43³ | C ³±
|
||
³ 26 (TERMPWR) to ground, and likely C/D < ³46 45³ | T ³±
|
||
³ damage the drive or controller. Also, REQ < ³48 47³ | O ³±
|
||
³ as explained earlier, the terminating I/O < ³50 49³ GND R ³±
|
||
³ resistors should remain only on the ÀÄÄÄÄÄÙ ³±
|
||
³ controller (Host Adapter) and the LAST ÚÄÄ¿ DB-25F CONN. ³±
|
||
³ drive on the cable, regardless of it's GND ³1 ÀÄÄ¿ ³±
|
||
³ address. DB1 <>³2 14³<> DB0 ³±
|
||
³ Most SCSI Host Adapters also have DB3 <>³3 15³<> DB2 ³±
|
||
³ a connector for external drives in the DB5 <>³4 16³<> DB4 ³±
|
||
³ form of a Centronics(tm) type 50 pin, DB7 <>³5 17³<> DB6 ³±
|
||
³ or an "alternate", DB-25F connector. GND ³6 18³<> PARITY ³±
|
||
³ Only the internal 50-pin, and the SEL <>³7 19³ GND ³±
|
||
³ "alternate" external connector are GND ³8 20³< ATN ³±
|
||
³ shown here. (see also: MORE SCSI) TMPWR ³9 21³ > MSG ³±
|
||
³ Also, these diagrams refer to the RST <>³10 22³< ACK ³±
|
||
³ single-ended SCSI connections, since C/D < ³11 23³<> BSY ³±
|
||
³ this is the most common arrangement I/O < ³12 24³ > REQ ³±
|
||
³ for PCs today. The Differential SCSI GND ³13 25³ GND ³±
|
||
³ requires balanced lines, and is used ³ ÚÄÄÙ ³±
|
||
³ mostly on high-end workstations. ÀÄÄÙ FUTURE DOMAIN³±
|
||
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ±
|
||
±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±
|
||
|
||
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
|
||
³ DIAGRAMS.DOC 5 ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ CABLES ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ SCSI (cont.) ³±
|
||
³ (T) ÚÄ(DC)¿ (T) ³±
|
||
³ On an SCSI cable, the 1ÉÍÍ»ÄstripeÄ1ÉÍÍ»ÄÄ1ÉÍÍ»ÄÄ1ÉÍÍËÍÍ»ÄÄ1ÉÍÍ» ³±
|
||
³ terminating resistors º::ºðððððððððº::ºðððº::ºðððº::º::ºðððº::º ³±
|
||
³ (T) remain at the END º::ºðððððððððº::ºðððº::ºðððº::º::ºðððº::º ³±
|
||
³ devices on the cable, º::ºðððððððððº::ºðððº::ºðððº::º::ºðððº::º ³±
|
||
³ even when 2 cables are º::ºðððððððððº::ºðððº::ºðððº::º::ºðððº::º ³±
|
||
³ "Daisy-Chained" (DC). º::ºðððððððððº::ºðððº::ºðððº::º::ºðððº::º ³±
|
||
³ Also, the external º::ºðððððððððº::ºðððº::ºðððº::º::ºðððº::º ³±
|
||
³ connector may be used, ÈÍͼ ÈÍͼ ÈÍͼ ÈÍÍÊÍͼ ÈÍͼ ³±
|
||
³ requiring the removal (HA) Drives 1-7 (in any order) ³±
|
||
³ of the Host Adapter's ³±
|
||
³ internal Term. resistors. ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ CONNECTORS ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ ³±
|
||
³ IDE (AT) HARD DRIVES (<> AT THE DRIVE CONN) ³±
|
||
³ ÚÄÄÄÄÄ¿ ³±
|
||
³ IDE, or Integrated Drive Electronics RST >³1 2³ GND ³±
|
||
³ is the most recent drive interface to SD7 <>³3 4³<> SD8 ³±
|
||
³ gain popularity. Often, the control SD6 <>³5 6³<> SD9 ³±
|
||
³ circuitry is built into the mother- SD5 <>³7 8³<> SD10 ³±
|
||
³ board, eliminating the requirement for SD4 <>³9 10³<> SD11 ³±
|
||
³ a seperate Host Adapter. There are 2 SD3 <>³11 12³<> SD12 ³±
|
||
³ types of IDE interfaces...those for the SD2 <>³13 14³<> SD13 ³±
|
||
³ 8-bit XT bus, and those for the 16-bit SD1 <>³15 16³<> SD14 ³±
|
||
³ AT bus (detailed here). The cable for SD0 <>³17 18³<> SD15 ³±
|
||
³ IDE contains 40 conductors and has no GND ³19 20³N/C (KEY) ³±
|
||
³ twists. Like an SCSI cable, the IDE RES.N/C³21 22³ GND ³±
|
||
³ cable uses a Dual-row Pin connector for IOW >³23 24³ GND ³±
|
||
³ both ends. A single cable may be used IOR >³25 26³ GND ³±
|
||
³ to connect two drives, or two cables RES.N/C³27 28³N/C RES. ³±
|
||
³ may be Daisy-Chained. Most IDE Host RES.N/C³29 30³ GND ³±
|
||
³ Adapters will support two hard drives. IRQ14 <³31 32³> I/O CS16 ³±
|
||
³ The first drive should be jumpered as SA1 <>³33 34³<> PDIAG ³±
|
||
³ the Master drive, and the second as the SA0 <>³35 36³<> SA2 ³±
|
||
³ Slave drive. Plug-in IDE Host Adapters CS0 >³37 38³< CS1 ³±
|
||
³ are often called Paddle-Boards, and ACTIVE <³39 40³ GND ³±
|
||
³ may contain a floppy controller, and ÀÄÄÄÄÄÙ ³±
|
||
³ serial and parallel ports. ³±
|
||
³ ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ CABLES ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ Note: ³±
|
||
³ 1ÉÍÍ»ÄÄÄÄstripeÄÄÄÄÄ1ÉÍÍ»ÄÄÄÄÄÄÄÄÄÄÄ1ÉÍÍ» ³±
|
||
³ The IDE Host Adapter º::ºððððððððððððððððº::ºððððððððððððº::º ³±
|
||
³ connector may be on º::ºððððððððððððððððº::ºððððððððððððº::º ³±
|
||
³ a plug-in Paddle-Board º::ºððððððððððððððððº::ºððððððððððððº::º ³±
|
||
³ or may be integrated º::ºððððððððððððððððº::ºððððððððððððº::º ³±
|
||
³ on the Motherboard. º::ºððððððððððððððððº::ºððððððððððððº::º ³±
|
||
³ ÈÍͼ ÈÍͼ ÈÍͼ ³±
|
||
³ Host Adapter Drives 1-2 (any order) ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ 1* There ARE some SCSI drives that utilize MFM, but very few. ³±
|
||
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ±
|
||
±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±
|
||
|
||
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
|
||
³ DIAGRAMS.DOC 6 ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ More on Recording ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ ³±
|
||
³ WRITE PRECOMPENSATION ³±
|
||
³ ³±
|
||
³ OK, so we've all seen it listed, and maybe even had to set it ³±
|
||
³ in the CMOS. So what IS it? And what does it do? ³±
|
||
³ PreComp. is the way in which the electronics compensates for ³±
|
||
³ eventual "drift" of the magnetic domains written on the disk. A ³±
|
||
³ simple explaination is that it allows the head to space bits that ³±
|
||
³ would attract each other, further apart, while it puts those that ³±
|
||
³ repel each other, closer together. It does this by analyzing the ³±
|
||
³ data stream, and adjusting the timing for each bit, to allow it to ³±
|
||
³ be recorded earlier or later, if needed. ³±
|
||
³ Not all disks require you to set their PreComp value. Those ³±
|
||
³ that do are asking for a cylinder to start PreComp. at. Since the ³±
|
||
³ packing of the bits on a disk increases as you get closer to the ³±
|
||
³ center of the disk (higher cylinders), the requirement for PreComp.³±
|
||
³ increases too. The PreComp. value specified by the Manufacturer ³±
|
||
³ for a disk is his way of insuring your long term data stability. ³±
|
||
³ ³±
|
||
³ ÄÄ< THE EFFECT OF PRECOMPENSATION OVER TIME >ÄÄ ³±
|
||
³ ³±
|
||
³ When recorded (w/o PreComp) When recorded (with PreComp) ³±
|
||
³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³±
|
||
³ ³ +- -+ +- +- -+ -+ ³ ³ +- -+ +- -+ -+ -+³ ³±
|
||
³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³±
|
||
³ ³±
|
||
³ After time (w/o PreComp) After time (with PreComp) ³±
|
||
³ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³±
|
||
³ ³+- -+ +- +- -+ -+ ³ ³ +- -+ +- -+ -+ -+ ³ ³±
|
||
³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³±
|
||
³ ³±
|
||
³ From the figures above, we can see how a slight amount of Pre- ³±
|
||
³ Compensation can insure long term stability. The disk that didn't ³±
|
||
³ employ PreComp was eventually unreadable. Of course, this would ³±
|
||
³ take time to happen, but no one can give cold hard specs on how ³±
|
||
³ much drift will occure. (Of course, this example is a gross sim- ³±
|
||
³ plification of the process, but, hey, who's counting?) ³±
|
||
³ ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ For Notes & Such ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ ³±
|
||
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ±
|
||
±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±
|
||
|
||
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
|
||
³ DIAGRAMS.DOC 7 ³±
|
||
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´±
|
||
³ APPLE SCSI ³±
|
||
³ ³±
|
||
³ Unlike in the PC world, the Apple APPLE DB-25 SCSI ³±
|
||
³ standardized on one drive interface, ÚÄÄÄÄ¿ ³±
|
||
³ SCSI. Also, Apple standardized on REQ < ³1 À¿ ³±
|
||
³ a 25 pin connector for external con- MSG < ³2 14³ GND ³±
|
||
³ nections. However, Apple decided not I/O < ³3 15³ > C/D ³±
|
||
³ to implement the complete ANSI spec., RST <>³4 16³ GND ³±
|
||
³ so one must be careful that peripherals ACK >³5 17³< ATN ³±
|
||
³ used are certified to work with Apple's BSY <>³6 18³ GND ³±
|
||
³ SCSI bus. GND ³7 19³<> SEL ³±
|
||
³ Apple also developed it's own pin- DB0 <>³8 20³<> PARITY ³±
|
||
³ configuration. The Apple and Future GND ³9 21³<> DB1 ³±
|
||
³ Domain 25-pin SCSI connectors are as DB3 <>³10 22³<> DB2 ³±
|
||
³ close to "Standards" as there are in DB5 <>³11 23³<> DB4 ³±
|
||
³ the world of PCs. But the real ANSI DB6 <>³12 24³ GND ³±
|
||
³ Standard called for a 50 pin connector DB7 <>³13 25³ TMPWR ³±
|
||
³ commonly referred to as a "Centronics" ³ ÚÙ ³±
|
||
³ type (made popular by the Centronics ÀÄÄÄÄÙ ³±
|
||
³ printer company). Instead of the 25 ³±
|
||
³ staggered pins of the Apple & Future 50-PIN "CENTRONICS" ³±
|
||
³ Domain type connectors, the Centronics TYPE SCSI ³±
|
||
³ type uses 2 parallel rows of 25 pins. ÚÄÄÄÄÄ¿ ³±
|
||
³ This arrangement allowed use of extra ³1 26³ ³±
|
||
³ grounds for better isolation. ³2 27³ ³±
|
||
³ ³3 28³ ³±
|
||
³ ³4 29³ ³±
|
||
³ ³5 30³ ³±
|
||
³ ³6 31³ ³±
|
||
³ ³7 32³ ³±
|
||
³ ³8 33³ ³±
|
||
³ (WORK IN PROGRESS) ³9 34³ ³±
|
||
³ ³10 35³ ³±
|
||
³ ³11 36³ ³±
|
||
³ ³12 37³ ³±
|
||
³ ³13 38³ ³±
|
||
³ ³14 39³ ³±
|
||
³ ³15 40³ ³±
|
||
³ ³16 41³ ³±
|
||
³ ³17 42³ ³±
|
||
³ ³18 43³ ³±
|
||
³ ³19 44³ ³±
|
||
³ ³20 45³ ³±
|
||
³ ³21 46³ ³±
|
||
³ ³22 47³ ³±
|
||
³ ³23 48³ ³±
|
||
³ ³24 49³ ³±
|
||
³ ³25 50³ ³±
|
||
³ ÀÄÄÄÄÄÙ ³±
|
||
³ ³±
|
||
³ ³±
|
||
³ THE END? ³±
|
||
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ±
|
||
±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±±
|